Browse Categories
Browse by Manufacturer
Mailing Lists
Search

Simpson A34Z Angle Clip Z Max


MSRP: $0.65
Price: $0.64
You Save: $0.01 (2 %)
Item Number: A34Z
Manufacturer: Simpson Strong-tie
Manufacturer Part No: A34Z

Simpson A34Z Angle Clip Z Max

Galvanized (G185) 1.85 oz. of zinc per square foot of surface area (hot-dip galvanized per ASTM A653 total both sides). These products require hot-dip galvanized fasteners or fasteners approved for use with ZMAX.

The larger LTP5 spans subfloor at the top of the blocking or rim joist. The embossments enhance performance and the min/max nailing option allows for design flexibility.

The LTP4 Lateral Tie Plate transfers shear forces for top plate-to-rim joist or blocking connections. Nail holes are spaced to prevent wood splitting for single and double top plate applications. May be installed over plywood sheathing.

The A35 anchor's exclusive bending slot allows instant, accurate field bends for all two- and three-way ties. Balanced, completely reversible design permits the A35 to secure a great variety of connections.

Material: LTP4/LTP5—20 gauge; all others—18 gauge

Finish: Galvanized. Some products available in stainless steel or ZMAX coating; see Corrosion Information.

Installation:

  • Use all specified fasteners. See General Notes.
  • A35 – Bend one time only.

These products are available with additional corrosion protection. Additional products on this page may also be available with this option, check with Simpson Strong-Tie for details.

These models are approved for installation with the Strong-Drive SD Structural-Connector screw.
See the load values.
Table
  1. Allowable loads are for one anchor. When anchors are installed on each side of the joist, the minimum joist thickness is 3".
  2. Roof loads are 125% of floor loads unless limited by other criteria.
  3. Some illustrations show connections that could cause cross-grain tension or bending of the wood during loading if not reinforced sufficiently. In this case, mechanical reinforcement should be considered.
  4. LTP4 can be installed over 3/8" structural sheathing with 8dx1 1/2" nails and achieve 0.72 of the listed load, or over 1/2" and achieve 0.64 of the listed load. 8d commons will achieve 100% load.
  5. The LTP5 may be installed over structural sheathing up to 1/2" thick using 8dx 1/2" nails with no reduction in load.
  6. Connectors are required on both sides to achieve F2 loads in both directions.
  7. NAILS: 8dx1 1/2 = 0.131" dia. x 1 1/2" long. See other nail sizes and information.

Simpson Strong-Tie A34A34SSA34ZA35A35SSA35ZLTP4LTP4ZLTP5

Related Products

Simpson A35Z Angle Clip Z Max
MSRP: $0.59
Price: $0.48
You Save: $0.11 (19 %)
Simpson A35Z Angle Clip Z Max
Simpson ABU44Z Adjustable Post Bottom/Base 4x4 Z max
MSRP: $21.11
Price: $14.73
You Save: $6.38 (30 %)
Simpson ABU44Z Adjustable Post Bottom/Base 4x4 Z max
Simpson ABU46Z Adjustable Post Bottom/Base 4x6 Z max
MSRP: $41.05
Price: $29.50
You Save: $11.55 (28 %)
Simpson ABU46Z Adjustable Post Bottom/Base 4x6 Z max
Simpson ABU66Z Adjustable Post Bottom/Base 6x6 Z max
MSRP: $45.65
Price: $30.29
You Save: $15.36 (34 %)
Simpson ABU66Z Adjustable Post Bottom/Base 6x6 Z max
Simpson AC4Z Post Cap Z-Max
MSRP: $4.89
Price: $4.18
You Save: $0.71 (15 %)
Simpson AC4Z Post Cap Z-Max
Simpson AC6Z Post Cap Z-Max
MSRP: $7.99
Price: $7.34
You Save: $0.65 (8 %)
Simpson AC6Z Post Cap Z-Max
Simpson ACE4Z Post Cap End Z Max
MSRP: $5.99
Price: $5.80
You Save: $0.19 (3 %)
Simpson ACE4Z Post Cap End Z Max
Simpson CS16Z Coiled Strap 16gauge 150FT Roll Z Max
MSRP: $206.33
Price: $172.21
You Save: $34.12 (17 %)
Simpson CS16Z Coiled Strap 16gauge 150FT Roll Z Max

Product Reviews

Rate This Product:
or Create a Review
(0 Ratings, 0 Reviews)