Browse Categories
Browse by Manufacturer
Mailing Lists
Search

Simpson SET56 Epoxy 56oz Double Tube High Strength


MSRP: $99.99
Price: $80.44
You Save: $19.55 (20 %)
Item Number: SET56
Manufacturer: Simpson Strong-tie
Manufacturer Part No: SET56
SET is a two-component, 1:1 ratio, high-solids, epoxy-based adhesive for use as a high strength, non-shrink anchor grouting material. Resin and hardener are dispensed and mixed simultaneously through the mixing nozzle. SET meets or exceeds the requirements of ASTM C-881 specification for Type I, II, IV and V, Grade 3, Class B and C.

USES

  • Threaded-rod anchoring
  • Rebar doweling
  • Bonding hardened concrete to hardened concrete
  • Pick-proof sealant around doors, windows and fixtures
  • Paste-over for crack injection

APPLICATION

Surfaces to receive epoxy must be clean. For installations in or through standing water, see Supplemental Topics for Adhesive Anchors for details. The base material temperature must be 40°F or above at the time of installation. For best results, material should be 70°–80°F at the time of application. Cartridges should not be immersed in water to facilitate warming. To warm cold material, the cartridges should be stored in a warm, uniformly heated area or storage container for a sufficient time to allow epoxy to warm completely. Mixed material in nozzle can harden in 5–7 minutes at a temperature of 40°F or above.

SUGGESTED SPECIFICATIONS

Anchoring adhesive shall be a two-component high-solids epoxy based system supplied in manufacturer's standard cartridge and dispensed through a staticmixing nozzle supplied by the manufacturer. Epoxy shall meet the minimum requirements of ASTM C-881 specification for Type I, II, IV, and V, Grade 3, Class B and C and must develop a minimum 12,650 psi compressive yield strength after 7 day cure. Epoxy must have a heat deflection temperature of a minimum 136°F (58°C). Adhesive shall be SET adhesive from Simpson Strong-Tie, Pleasanton, CA. Anchors shall be installed per Simpson Strong-Tie instructions for SET adhesive.

SHELF LIFE

24 months from date of manufacture in unopened sideby- side cartridge.

STORAGE CONDITIONS

For best results store between 45°F – 90°F. To store partially used cartridges, leave hardened nozzle in place. To re-use, attach new nozzle.

COLOR

Resin – white, hardener – black. When properly mixed SET adhesive will be a uniform light gray color.

CLEAN UP

Uncured material – Wipe up with cotton cloths. If desired scrub area with abrasive, waterbased cleaner and flush with water. If approved, solvents such as ketones (MEK, acetone, etc.), lacquer thinner or adhesive remover can be used. DO NOT USE SOLVENTS TO CLEAN ADHESIVE FROM SKIN. Take appropriate precautions when handling flammable solvents. Solvents may damage surfaces to which they are applied. Cured material – Chip or grind off surface.

SET Cartridge Systems
 
  1. Bulk containers also available, contact Simpson Strong-Tie for details.
  2. Cartridge and bulk estimation guides are available.
  3. Detailed information on dispensing tools, mixing nozzles and other adhesive accessories is available.
  4. Use only appropriate Simpson Strong-Tie mixing nozzle in accordance with Simpson’s instructions. Modification or improper use of mixing nozzle may impair epoxy performance.
 
In-Service Temperature Sensitivity
  1. Refer to temperature sensitivity chart for allowable bond strength reduction for temperature. See Supplemental Topics for Adhesive Anchors.
  2. Percent allowable load may be linearly interpolated for intermediate base material temperatures.
  3. °C = (°F-32) / 1.8
Cure Schedule
 

Product Reviews

Rate This Product:
or Create a Review
(0 Ratings, 0 Reviews)